Can I Vent My Dryer Into the Garage

I've been doctoring appliances and electronics for a number of years. I'1000 here to share the knowledge and experience I've nerveless.

There are a number of possible causes of this problem.

Photograph by Andrew Winkler on Unsplash

Then, your clothes dryer won't produce heat? There are a number of possible causes of this problem. The first affair we must determine is the blazon of dryer you have. At that place are simply two types: gas or electric.

Alert: Before Yous Brainstorm

Earlier attempting to repair any appliance:

1. Turn off (unplug or kill the excursion to) electrical power.
2. Close off gas supply (if applicative).

Caution! Shut off all the power before you brainstorm!

Step 1: Cheque the Power

If your dryer is electric, pregnant it uses electricity instead of flame to produce rut, stride i is to verify that the breaker to the dryer's electrical circuit is fully on. Since electric dryers crave 240 volts to run, their circuit is run through a dual breaker switch. Sometimes simply half of the billow switch will be off, or will have failed, which may result in a supply of only enough power to make your dryer tumble but non plenty for it to produce oestrus. Pop the breaker to your dryer off and on again and then see if the dryer will now produce heat. If it does, so have the breaker replaced. If information technology doesn't, you tin verify that the dryer outlet is fully powered past testing it with a voltmeter. If the electric outlet is fully powered, and then the problem definitely rests within the dryer.

If your dryer runs on gas, we will assume there are no kinks or stoppages in the line and the problem is in the dryer itself, although if you follow all the rest of the steps and nonetheless can't discover the solution, you might investigate this every bit a source of the trouble.

Continuity tester

Stride two: Check the Dryer'due south Internal Workings

Allow's next deal with the failure common to both types (gas and electric dryers). Y'all will demand a continuity tester for this process. Here are directions for how to utilize a continuity tester.

After you have disconnected the power or close off the gas, y'all will want to access the internal workings of your dryer. Directions for achieving admission, specific to your brand, can be found in your owner's manual. If you lot don't take one, you might endeavour Google or searching YouTube to encounter if anyone has uploaded instructions for your detail make or model.

Most dryers have a thermal fuse located in the exhaust path. Depending on your dryer, the fuse will exist found toward the front end or the rear of your unit. Generally, if at that place is a removable back on the dryer, and then that is where you volition find the fuse.

The most commons thermal fuses you lot might find are shown in the analogy below. They are each roughly i" in size. You lot volition notice that the contact points are hands spotted for a continuity exam.

In older units and in some electrically heated units, at various points along the heater assembly you lot volition detect a series of thermal fuses that look similar small tin cans. These will also need to be continuity tested before you can dominion out thermal fuses as your problem.

If any of the thermal fuses fails the continuity examination, and then information technology needs to be replaced.

Your thermal fuse might look like this

Read More than From Dengarden

Step three: Check the Heating Chemical element (Electric Dryer)

Later on making certain your thermal fuse(s) is/are proficient, information technology is fourth dimension to move on to the next most probable possibility: the heating element. This element is comprised of metallic coils supported on a framework with 2 contact points where wires are connected to the rest of the dryer. A break in this coil will stop the dryer from being able to create heat. Examination the two contacts for continuity with a continuity tester. If they fail, then y'all demand a new heating element.

If both the thermal fuse and the element show continuity, information technology is fourth dimension to telephone call a professional to service your electrical dryer.

Typical dryer heat element

Step 3: Check the Burner Assembly (Gas Dryer)

Gas dryers utilize a burner system to create heat. This system has a number of parts that tend to fail over time: Some you tin test but some you must simply read the signs and make a adept estimate to supercede or not to replace the office.

Not all of these parts can be tested with a elementary continuity tester. An ohm meter is now required to find your problem function.

The parts prone to failure in your burner associates are:

• Igniter
• Coils
• Flame sensor

A burner operates in a fairly elementary mode. Once the motor is turning, centrifugal force closes the motor switch, allowing the electricity to reach the flame sensor. The flame sensor allows the electricity to reach the igniter, allowing it to heat up to a temperature high plenty to ignite natural gas. Once the igniter is hot enough, the flame sensor breaks the igniter circuit, allowing the electricity to run through the coils that open the gas valve. Gas then flows out past the igniter and catches fire. The heat is drawn into the airflow within the dryer.

Internal workings of a gas dryer: burner assembly

Troubleshooting Gas Dryers

Ascertainment is cardinal to troubleshooting a gas dryer. Does your dryer get hot at the beginning of the run but finish cold? Does information technology never rut at all? Exercise you hear a chattering sound at times?

If your dryer is hot at the starting time of the run but finishes cold, then it is likely yous have bad coils. As coils age, they lose the ability to concur the gas valves open. Sometimes this volition cause the valves to open and close rapidly, resulting in a chattering sound. Unfortunately, you tin't test the coils to verify the failure, and so replacing them is a decision yous make based on the above observations.

If the dryer never heats, so there are more than items to check and examination. The first item is the igniter. In that location is a molex (clear plastic) connector attaching the igniter to the burner circuit: Disconnect this and place your ohm meter probes onto the two contacts on the igniter side of the connector. The meter should read under 100 ohms of resistance. Any reading above this value means that the igniter needs replacing.

If the igniter passes your test, then you need to exam continuity on the flame sensor. You lot should have continuity between the 2 contacts. If not, then you need to supervene upon the flame sensor.

If all of the in a higher place pass their tests, yous need to make certain that at that place isn't a build-up of dryer lint around the burner. Sometimes, lint will impede the gas flow, preventing the unit of measurement from igniting.

If none of these things help, then it is time to call in a professional.

This article is accurate and true to the best of the author's knowledge. Content is for informational or entertainment purposes merely and does not substitute for personal counsel or professional advice in concern, fiscal, legal, or technical matters.

Mike Morrison on December 18, 2017:

I have a,whrpool lp gas dryer the igniter come on the flame starts and burns, but is only about ii-3 inches long. I watch other gas dryers and the flame wait large enough to fill the burner tube, any ideas?

I checked gas menses, replaced the coils and the igniter?

Phil on November 28, 2017:

I accept a whirlpool gas dryer..it runs but does non oestrus. I looked and in that location is now glow. Would this be a adept possibility of thermal valve?

Sheree Rowse on June 17, 2017:

They put new chemical element in moms dryer worked3 days and now no heat?

jenn on April 16, 2017:

I replaced my heating chemical element, thermostat and thermal fuse all at the same time, i was able to do 2 small loads of laundry before it stopped heating again. Checked all parts for continuity again and the thermal was open up.then information technology blew out simply after drying 2 loads of laundry???.... I only bought all three of these parts and put them in right before i done the 2 modest loads of laundry... Why did information technology accident already? Lint is clean and electricity is fine to the plug in the wall. Electrical panal is fine...

John J Hoban on March 06, 2017:

replaced coils, ignitor and fuse still won't estrus whirlpool dryer

Vinny on September 19, 2016:

Hi guys I have a Kenmore gas dryer from Sears. I remember once when a load stop drying as I was taking her clothes out and the car was not running I spun the drum and I heard something click and since then the dryer is not heating whenever I cycle it for a dry model # 11070172002. Thank yous in advance your output really appreciate it.

Robert s on September 14, 2015:

How do I know which switches in my billow box control the dryer outlet?

Traci Tucker on July 23, 2014:

I had this problem with my Coldstream dryer recently.

I wrote a mail service well-nigh information technology. This volition assistance you hands gear up your dryer within 30 seconds and for gratis.

http://traci-tucker.com/2014/07/coldstream-dryer-i...

Good luck

Todd Capparello on July 21, 2014:

I take replaced fuse igniter and now gas coils. Withal tin can't get get dryer to rut upward. Tin you help me with this?

Nelson on June xiii, 2014:

This site has a lot of cracking info simply I don't know if the Appliance Doc ever made it back to wellness. Sad

Steve on February 23, 2014:

I have an older model GE gas dryer. The heat comes on for one or two times and so runs cold the remainder of the dryer cycle. Sounds like the coils based on my enquiry but I checked the coils with an ohm meter and they seemed to be ok. Any ides?

roberto on February 07, 2014:

I have a GE GAS Dryer Model DCVH680GJ2WW bouth five/7/2010 and information technology does not accept heat, my Igniter reads 185 ohms, I read above that information technology should exist less than 100 ohm, I measure an Inlet control thermostat # 507, and a thermistor #240 and both shows open, I social club a new parts and both shows open too, all the other parts in the dryer thermostat and thermistor reads OK, is the Igniter 185 ohms bad, and the thermostat and thermistor both open bad besides.

Please help

Kerry Allen from SE Texas on November 17, 2013:

Hey Dr.

I simply purchased a gas GE Dryer used and everything works except there is no rut. In reading your commodity, yous accept a reference to figure three just I can't discover information technology...

Am I just not seeing it?

garett on Nov xi, 2013:

My kenmore gas dryer works information technology spins but no heat. If changed the coils and nonetheless no heat. We watched the ignitor information technology glows upwards and seems like it wants to ignite just the glow disappears. Similar its non getting any gas to ignite. Could it exist the gas valve on the motorcar? When it starts up it sounds normal only then after couple seconds it starts making a funny buzzing racket. And so it will go abroad and come back..while that noise is happening the ignitor repeats itself to try to ignite.

bart clovis on November 09, 2013:

ive replaced the heating coil in my older whirlpool dryer and information technology tumbles merely does non become warm

Paul on October 16, 2013:

Whirlpool CGM2941TQ1

The dryers gas valve mysteriously self ignites. No coins no manual reset, simply cycles on and off like it was normally running. The pulsate does not turn when this is happening.

Please help! Thanks for your input. Paul

chris carney on March 24, 2013:

my dryer spins and the heating element tested ok and the thermal fuse tested ok but it however wont heat. the vent isn't clogged either. it did work last night but only 1 load. Help?

jostler2013 on Feb 06, 2013:

Thanks for the help, I've had some of my own troubles with dryers. Some of the biggest bug I have is that the heating element will go out. I like to practice nearly of my own repairs but sometimes I just don't have time. If you are always in demand of an apparatus repair in naples, you'll have to check out these guys http://www.alwaysspeedyapplianceservice.com, they've always seemed to be a great alternative for when I can't fix it myself.

james on December 17, 2012:

my dryer volition not haet upwardly

Cliff on July thirteen, 2012:

My Performa dryer (by Maytag) would burn down the outset time, merely that was it. Timer wouldn't movement (manifestly information technology only moves when the flame is on). I checked the coils with a meter, and they measured spot-on (run across above). Nevertheless, I saw other people had the same issues, had expert readings, and yet replaced the coils. I found a set up for less than $8.00, including shipping, so in that location was lilliputian risk in replacing them. Once replaced, the dryer is working fine, and the timer operates correctly equally well. And so my story is basically that the coils were weak and failing, even though when I'd checked them with an ohm meter they appeared to exist fine. If your dryer does burn down, but only once, or intermittently, try replacing the coils... It can't be the thermal fuse or sensors if the gas still comes on at all. It likely isn't the ignitor if you get a adept, bright glow. Supervene upon the coils - worked for me.

Claire on June 10, 2012:

I take a gas dryer won't oestrus as of yesterday afternoon. It does turn on. We had power out in a few outlets in the business firm one on the same wall (opposite side) of the dryer. I think somehow the pilot went out? Any suggestions?

Thanks!

patfussy on May 26, 2012:

I have an admiral electrical dryer,it died on me and through different channels figured out information technology was a bad thermal fuse. I replaced it and the dryer is running again...only now it won't heat up. Any assistance would exist profoundly appreciated.

Alex on May xiv, 2012:

Not getting igniter glow on a (Whirlpool) lxxx-series Kenmore gas dryer. Checked thermal fuse outset, resistance is well-nigh naught. Checked igniter, looks skillful and resistance is 76 ohms. Suggestions on what to await for side by side? Thanks for your help.

Tim on April 17, 2012:

On an electric dryer should yous encounter sometimes see a glowing or calorie-free at the bottom of the dryer? We had ours out from the wall afterward we had cleaning out lint from the duct. As well should the dorsum where information technology sticks out on the left side feel really hot?

Thanks for any help.

Gman on April 15, 2012:

I have a whirlpool electric dryer that wont heat , I have replace the thermal fuse , heating element and the piece that goes into the heating element and even so does not go hot . Flip the switch on the fuse box , is there annihilation else that I need to practice .

Dot on March 29, 2012:

I have a kenmore 90 serial and it runs simply does not go hot...we do non encounter any flame when turned on

Mike Northward on March 28, 2012:

Read previous blogs (thank you) approx 2 years agone replaced 2 bad gas valve relays to solve dryer heat on /off trouble & replaced ignitor for proficient measure. At present ignitor does not glow when dryer is running, measured 75 ohms & inspected ignitor which nevertheless looks new. Tested flame sensor, 0 ohms & checked relays which checked OK. Pulsate rotates and no obstructions in vent or dryer. What next?

Lori on March 24, 2012:

I tin see a coil low-cal upwards just no flame. Whatsoever suggestions? Gas Dryer.

DAR on March 20, 2012:

my dryer works and then shot off by it self we accept to wait until cools off.likes over heats....help me please.

frieda on March sixteen, 2012:

i accept replaced the heating element the thermal fuse checked the breaker its good and the dryer notwithstanding has no oestrus so what else could it be

wallytiger on March xi, 2012:

To follow upwardly on my Amana dryer: obviously replacing the thermal fuse lonely did not practise the trick. I had to change the thermostat too. One time both were changed, my dryer has been working since.

Jim on March 09, 2012:

I take a Kenmore Ultra Fabric Intendance 27" gas dryer. I get no heat although the dryer works fine otherwise. I accept already replaced the thermostat and tested the Igniter, which got 69.five ohm. I besides tested the flame sensor and thermal fuse and have continuity on both. I'thou at a loss where to get from hither. I as well had the temperature control switch off, just could not tell if it was bad and couldn't locate a replacement. I have the dryer pulled apart, any help would be appreciated.

Bo on March 07, 2012:

Great path to diagnosis - thanks for laying it out for me! I took the fuse off today - and I'm getting a new i this weekend. I promise it works - merely even if it doesn't, yous actually laid out the options perfectly. THANKS FOR THE HUB Page!

wallytiger on February 21, 2012:

I take an electric Amana dle330raw dryer that a wire to the thermo fuse cutof blew. The thermo fuse cutof works but test shows the thermo fuse itself is bad. i replace the thermo fuse and the dryer worked for a day and the same wire going to the thermo fuse cut of blew again

jkunkels@aol.com on Feb xix, 2012:

bypassed the thermal fuse and was working fine so ordered a new 1. In the mean fourth dimension I moved information technology while it was running and the featherbed shorted out, and now is not working again. What to bank check next.

ale on February 08, 2012:

my dryer does estrus upwardly later on half dozen hrs running and it takes like 4 hrs to dry my cloths what could be wrong?

Enzo Piccinini on January 31, 2012:

@ thebombsteak

1) replaced the glow igniter - STILL NO GLOW

2) replaced thermal fuse - All the same NO GLOW

3) replaced coils - STILL NO GLOW

----Endeavor testing the flame sensor, one of the more than common part to get out.

Penny on Jan 21, 2012:

After changing the solenoids, the problem persisted. The gas would light for most x seconds and then shut off pretty much for adept. My wife pointed out that there'southward was no lint in the filter. So I started thinking "clog" somewhere inside the dryer. Only afterward fierce the matter apart front and back did I recollect to wait INSIDE the dryer. Viii softener sheets were fused to the exhaust outlet! Ho ho! That was like shooting fish in a barrel!

Jess brewer on Jan 21, 2012:

Our dryer won't calorie-free up or put out heat would that be the heating element or something wrong with our breaker. It worked with a large load of apparel in information technology terminal nighttime only I places a smaller load in it today an information technology won't estrus. The dryer kept blowing the billow final night could that have something to practice with why information technology won't piece of work now?

charles new york on January 12, 2012:

i have a whirlpool gas dryer stopped drying i changed the ignitor still no rut Please Assistance

al on December twenty, 2011:

I take a Maytag dryer I change coils and thermostat. Before the igniter wasn't working. and that trouble solved only correct now "when I shut the door and start, there is no heat. the igniter comes on but the pilot light doesn't plough on, merely when the door is open and printing the door switch to make it start, the pilot works and the dryer is working fine. I was thinking information technology'southward an air circulation problem maybe the air goes to the airplane pilot and blowing straight to the pilot. I tried to find the problem but tin can't trace any. Any Ideas.

Joe on December 12, 2011:

I accept a strange one. Am renting the firm, then when not heat, the possessor replaced information technology. Nigh ten days afterwards, no heat again, with a NEW dryer. The ignitor glows but shuts of in almost 10 seconds. Therefore the problem is outside the dryer, correct?!!?

I tin run across gas supply valve is open, and electrical is good (drum spins, ignitor glows) but no heat. Wondered if it was able to observe jammed exhaust pipage (ours goes to rooftop) so I removed the vent pipe and IT WORKED... ignitor, fire, oestrus, and dry apparel. Merely just once. Now with vent pipe removed we get no heat nevertheless. Suspect gas at present?

HarryJ on Nov 15, 2011:

I have a Whirlpool Electric Dryer Model # LEC 8858EZO for a few years. No problems so far and today I find that the clothes when stale are not warm. Looks like the heater is no working. Any guidance/suggestions/recommendations delight would be appreciated. I am unemployed and cannot afford to buy a new one. If I tin repair it myself, that would help me. Thanking you in advance. HarryJ

Mike on Nov 04, 2011:

Greg, I had the aforementioned problem, information technology ended upwards being a thermistor located on the blower of my kenmore elite dryer.

Billgator on November 04, 2011:

I replaced my solenoid coils and at present my gas dryer functions properly. See my in a higher place post for the symptoms.

Rey on Nov 04, 2011:

Hullo Justin, Im non the Doctor or a pro but the commencement thing i e'er check is the Thermal fuse (near common prob i encounter) if circuit is open replace...

justin on November 03, 2011:

i have a whirlpool gas dryer and i have NO oestrus at all,ive changed the •Igniter

•Coils

•Flame sensor

what else could peradventure be wrong im non very handy but i cant afford to replace the dryer what else can i do?Delight help thank you

Billgator on October 31, 2011:

I have a Whirlpool gas dryer model LGQ8858HZ0. My dryer starts up and runs with flame for 4-5 minutes. The flame then cuts out and the dryer volition every few minutes effort to reignite. Nice glow from the ignitor but no ignition. There is also a funny sound preceeding the ignitor glow which sounds similar a penney sliding around in the pulsate. Non banging around but sliding. If you let the dryer absurd down it will reignite only then kill the flame after iv-v minutes.

greg douthit on Oct thirty, 2011:

Have Whirlpool elec dryer. replaced both fuses and curlicue. Worked for a couple of days now dorsum to no heat.

aa8rv on October thirty, 2011:

Hi,

I'm suspecting a bad thermal fuse on my Kenmore 27 inch electrical dryer as the reason why information technology runs but does non dry. Where can I get this thermal fuse for my particular model? And more importantly, I got confused on the wiring points to the three separate units that are on the heating chemical element vent including the thermal fuse(in other words, which wires go to each fuse) I run across that the wire prongs are different in size on some wires and that helps.

Thanks

linda on October 26, 2011:

my dryer wont heat up

Tim on October 05, 2011:

When I start the dryer information technology turns on then there is a loud click and I tin can see the burner low-cal with a big flame. A short fourth dimension later it goes out and stays out. No smell of gas just wont re-low-cal. Afetr a few trys...its repeats....on, click, flame....out. Please assist! Thanks, Tim. tbusb@comcast.internet

crystel rodriguez on September 26, 2011:

hi!i have a kenmore electric dryer,it doesn't brand heat and the timer knob don't rotate. what could it be.

Jemma on September xviii, 2011:

Thanks for the assistance. Likewise Jenni I am going to have to agree with things going out faster because they are cheaply made now. My parents take the aforementioned one they had when I grew upwards. :three

Dolly on September 01, 2011:

We bought a dryer at a moving sale and information technology is farely new. The dryer was in working condition when we got it and nosotros did see it run and information technology did put out rut, we loaded it up and brought information technology abode and now won't heat. Information technology tumbles and works like that, merely no heat at all. It is a GE dryer and the model # is DBSR453EB3WW.

Jenni012578 on August 27, 2011:

Is the heat going out common, my dryer is only 6 years old. I remember my mom having her dryer 30 earlier she had problems LOL I will have my hubby endeavour these things first. Thank you for trying to assistance us save a few bucks. Holiday is comimg quick :)

Rick Spero on July 31, 2011:

My dryer stoppped heating and I constitute your website. I saw your troubleshooting steps from 2 years agone and tracked the trouble downwardly to a bad thermal fuse. Thanks so much for your advice!!!!

Linda on July 27, 2011:

Being a contempo widow, I had no idea why the dryer would run but didn't have any heat, or how to fix information technology. Later reading the article I turned the circuit billow on and off a few times, and information technology worked! Thank yous

mary Smith on July 14, 2011:

go out side and run a moisture and dry out vac in the lent trap exterior and suck up all the water then your dryer will work I had to practise that the other day at present mr dryer dried my clothes real fast.

mike on July 10, 2011:

I have replaced the coils on my maytag dryer. I checked the ignitor and it is getting continuity simply information technology is not glowing. Is my problem with the thermal fuse(dryer runs simply not heating)or is my trouble the ignitor?Thank y'all for your answer! mleh1228@aol.com

Tim S on July 04, 2011:

I accept a gas maytag dryer and it is about 10 yrs quondam. I unplugged the unit and checked all the fuses. All have continunity except the heat sensor. My problem is that the igniter does non get hot because it is only getting 28 volts to it, then it will not trigger the heat sensor which tells the gas valve to open. Why am I only getting 28 volts to the igniter?

mtleggat on July 01, 2011:

I accept an electric whirlpool dryer and the oestrus doesn't work and neither does the timer (on both auto and manual). I tested the thermal fuse and it has good continuity....whatever suggestions?

Matt

Jim N on June 17, 2011:

GE electric dryer cycles on and off takes long time to dry clothes.

margie100 on June 04, 2011:

the dryer wont rut.I do believe it mite be the volts crusade this is the 3-4th dryer I've been thru the first three wre used simply this ane is new so do you lot think it could exist the voltage?that dsoes entail checking the billow rite or is the breaker on the dryer?Delight answer before long cheers

caleb on June 02, 2011:

Whirlpool gas dryer. Igniter heats up for a few seconds then goes out. Replaced coils. Same thing. What is the next step?

Lightnin Jones on March 08, 2011:

I accept a GE DDG7985SBLWW gas dryer that isn't heating. Drilled a hole depression in the burner side of cabinet to view "the glow" - no glow. Then I ran continuety tests on all electical "doo dads" I could see and detect. It all tested ok on ohm meter - 3 thermostats, igniter, both coils, heat/flame sensor, and belt tensioner switch - all beeped on my tests. But upon my checking voltage at the connector to the igniter, expecting 110/115v I had no voltage at all. Thought mayhap because the motor/chugalug switch was "open" from the belt being off, voltaged was cutoff from motor to the heating excursion. Leaning towards reported difficulty in obtaining accurate coil readings, I went and bought new coils and just to be certain, I thought, a new round igniter. Reassembled and tried information technology - still nothing . Motor runs fine, but still no glow, no ignition of gas, and upon rechecking, no voltage at the igniter connector. Schematic indicates under these conditions to test and confirm function at flame "detector", Timer TA TB, Heat Switch (? 1 of the 3 "stats" at back of heating sleeping room up on duct leading to disperser, that I checked and were ok?), Motor Switch 1&2 (only ane I see is Belt SW)and last just not least - thermostats. I even checked the "EOS" side by side to the timer and no electric current or beep. I didn't really empathize the TA TB role, can't say on success or not. in that location is a little gizmo wedged on the motor winding itself with crimson wire ,looks like, leading into winding. All ducting is spotless, vent is way costless. I ws thinking about buying the flame detector only becuz, but have reservations about the lack of voltage at that igniter connector. Whatever thoughts? Thanks in advance.

David on March 03, 2011:

I have a Kenmore gas dryer and take no heat. I outset inverse the ignitor and then the radiant sensor. Both have not helped and seems like no electric is getting to ignitor, since information technology'southward not lighting. What practise you think is effect? What regulates electrical to the ignitor? Is in that location a fuse or switch issue?

Tami on Feb 16, 2011:

My fridgedair gas dryer gets warm only not hot. When I outset the dryer it turns on then in that location is a loud click and I tin can come across the burner light very brightly. After a few seconds the glow dyes down and at that place is a slight glow but not very vivid, then it goes out. It does however seem to cycle, relighting and the same thing occures. The dryer does seem to exist blowing luke warm air only does not get HOT. I thought it was the ignighter but at present I meet that information technology is lighting. It seems it will not concord its initial heat. I cleaned information technology very well, with no success. Information technology is not real old simply has seem alot of utilise. Everything else seem to be in tip summit condition only with very lilliputian heat. Tin you help me trouble shoot this problem. I am very mechnically inclined, but as the parts are non cheap I don't desire to over shoot the trouble

kelvingriffith on February 13, 2011:

kenmore dryer-gas.problem I idea was an electric ignitor. I replced information technology it didn't glow. now I wondering is could it be the flame sensor? is information technology the office that prepare on tin housing,square piece with the word them-o-disc?

Johnnie on Feb 13, 2011:

Same equally above, I take an electric dryer which will estrus up for 1 minute then shuts off for one minute all though out the cycle. I've changed all three Thermal Fuses. Your help is welcomed. Cheers

joe on January 28, 2011:

i have a GE 2 cycle electric dryer model #DDE5100RALWH with the same trouble as sams above, the tumbler comes on with the heating element but the heating element shuts off after about 15-60 seconds... n due east suggestions Aplliance Medico!?!?

Sam on January 22, 2011:

electric dryer heating element heats up (glows) for about a minute and so shuts off. Motor running and air coming from frazzle. Should I replace the thermostat

KirkNY on January xviii, 2011:

I have a Maytag LSG7806AAE stacked gas dryer that has completely dumbfounded me. I consider myself a pretty competent DIYer and can't figure out this outcome and hoping you may be able to provide some insight. When I start the dryer the ignitor heats upwardly, the coils release the gas valve and the flame starts. The ignitor then turns off and the flame continues until the ignitor is no longer glowing. In one case this happens the coils click and shut off the gas valve. This happens throughout the unabridged drying cycle and results in very little heat to the clothes. I have replaced the coils as that was an immediate concern of some other person I reached out to for help but that did not change anything. I have checked and confirmed continuity with the thermal fuse, the gas cycling thermostat's outer ii contacts, the cycling thermostat, as well every bit the thermal sensor. At this bespeak I call back I've eliminated all potential issues - any I'one thousand missing? Please help!!!!

Lisa on January 17, 2011:

sorry didn't mention, gas dryer thx

Lisa on January 17, 2011:

Whirlpool LGR663 series, not heating, ignitor lights, flames for 30 seconds and then click and off, ironic as was repeating this process till i replaced the hilimit thermostat,now no repeat only goes out, I take replaced the coils, the ignitor, both thermostats, apparatus parts store told me that the it was not the flame sensor that those never are really the cause, help, I am out of parts and patience. thank you

Rebecca on January 15, 2011:

We have an electrical kenmore dryer, information technology tumbles fine merely no heat nosotros have changed the breaker (thing in the box in the basement), the heating element in the dryer and those can looking fuses and still no rut. What we nosotros missing?

thebombsteak on January 14, 2011:

Hello there,

Hoping you can help!

i take a Kenmore seventy series gas with NO glow from the glow igniter, then I:

1) replaced the glow igniter - All the same NO GLOW

two) replaced thermal fuse - Nevertheless NO GLOW

three) replaced coils - STILL NO GLOW

can you PLEASE let me know what direction i should be looking now? Thank you lot!

Kevin on Jan 13, 2011:

Hi there,

Hoping you tin can help!

i have a Kenmore 70 series gas with NO glow from the glow igniter, so I:

1) replaced the glow igniter - Nonetheless NO GLOW

2) replaced thermal fuse - STILL NO GLOW

3) replaced coils - Nevertheless NO GLOW

can you Delight permit me know what direction i should be looking now? Thanks!

honuski on December 21, 2010:

I followed your instructions and establish my igniter to be bad (cracked no reading). I replaced it and I'm back in business. Give thanks You Very Much and Merry Christmas> : )

Scott West on December 15, 2010:

no heat in kenmore gas dryer. changed the ingnitor, nevertheless does not glow. dont take a multi meter, what i next logical part?

this is the nigh informative site so far, by far!

acehoser on November xv, 2010:

I've cleaned out the lint throughout the dryer and vent, but when I have the vent pipe connected the dryer will oestrus, then shut off after nearly 10-15 seconds. If I disconnect the vent, the gas flame stays lit. Is this indicative of a faulty ringlet? I've swapped the thermister.

Millie Viera on November 13, 2010:

Where do I find the heating element in a whirlpool dryer

Kebeh on Oct 31, 2010:

My dryer is working but, there's no oestrus coming from it, therefore my apparel won't dry. I'm totally clueless of what to do because I accept no knowledge of machines. HELP!

sarahscott85 on October 21, 2010:

I've adamant with my electric dryer that my outlet is bad. It tests for 110 five on each side, but I don't get a 240 v reading... which is why it is running, but no rut. What at present? Do I need new breakers or an electrician to rewire a whole new outlet?

Shaun on October 07, 2010:

I have a Whirlpool gas dryer. There was no heat so I adamant I needed a flame sensor. I've replaced this and it heats up for about 10 min then the light goes out and no more heat. I've cleared all lint....tin can't figure out why it will estrus for 10 min and then the airplane pilot goes out? Suggestions?

Daniel on October 05, 2010:

Cheers and then much for laying this out. After reading this I was able to solve the problem in no fourth dimension.

Hannah on October 04, 2010:

My eight year quondam gas Maytag dryer quit drying. I took the front comprehend off to encounter if the igniter was working. It was. The gas came on fine and it heated. I cleaned all the lint out and vaccumed inside the motor expanse and then vaccumed the vent duct. I put it back together, put my apparel in and it didn't rut once again. I repeated the entire procedure again and over again, it ignited fine while I had the front end comprehend off. I even disconnected it from the vent duct just to see if it wasn't venting and tested it many times. Every time, it ignited just fine. Information technology seems to not heat when the front end embrace is on and it has clothes in it. Any ideas?

Jason on September 29, 2010:

I take a Maytag dryer (MDG308DAWW). The dial was non advancing in "car" dry mode. It would accelerate in timer fashion..but dress were not drying. Information technology would heat for virtually 4-5 mins, and thats information technology. I took the front end off the dryer(leaving the door switch wires connected), and watched the burner. Information technology would low-cal the first 2 times only not the 3rd, 4th, 5th, etc...times. After reading these posts (and conformation from my local appliance store)...I replaced the gas coils. Perfect! My dryer works now. Thanks Appliance Dr.! For $xxx I have a dryer that works like make new...it could've been at to the lowest degree 5 times that amount if a service tech made a visit. Promise this helps some of you out.

Bryan L on September 22, 2010:

Hi. I take an admiral gas dryer that heats up for awhile and then cools off and more often than not doesn't finish wheel, just keeps running. Timer makes a constant noise in the 30min time mode, which I don't e'er use til recently. Is this a bad timer or cause by bad coils. I have tried to clean out all grit/lint thouroughly. Thank you for your assistance!

Ken Coley on September 19, 2010:

How-do-you-do

I am checking the thermostats in my Alliance Gas Dryer but one has six connections (511957) how tin I test this? Besides I accept just found one other thermostat on the burner housing, it tests fine, are there whatsoever more I could be missing? I tested the igniter it was fine, then dropped it and it broke:) Symptoms are that it spins merely igniter doesn't warm upward, so assume thermo failure?

Thank you in accelerate!

Ben L on September 19, 2010:

Thanks and then much for the helpful troubleshooting. I followed the suggestions in the Maytag repair instructions(Modernistic gas dryer) and ended upwardly buying a command lath($200) when afterward post-obit your guide, found out it was the ignitor.(500,000 Ohm resistance) The guide had me only checking the thermister, thermal fuse, valve resistance etc...Not the ignitor resistance! Unfortunately, I deceit return the lath, simply have learned a great deal in the process. I'll come here offset next time!

Jim on September 08, 2010:

Hello,

I take a Whirlpool gas dryer. No heat! I looked into the portal and restarted the unit and the glow igniter does non come on. Took it to a parts guy and he tested it at 55 ohms and said it is good. I took the two thermal fuses off of the back and the one sparse white fuse equally well off and volition be taking it in for testing as well. My question is ....if any ane of these fuses are shot will it forbid the igniter from glowing? I assumed that they observe rut not certain if they "communicate" with the igniter itself. Too is it normal for the ii thermal fuses to rattle when shaken? Sounds like something loose in the disc part of the fuses. I know...featherbrained question!

priscilla1952 on September 05, 2010:

The flame sensor connection is broken. No rut, so why...

Why would you lot need to disconnect the gas line on a gas dryer if the dryer in non plugged in for power?

Jennifer on September 04, 2010:

Whirlpool gas dryer, push button kickoff button dryer comes on and drum spins, glow, gas comes on, starts to heat and after and then the gas goes on and off like information technology should but does not stay on long plenty to heat and then starts to brand a clicking noise when trying to rut. Took dryer autonomously many many times. Delight help.

Joe on September 03, 2010:

Kenmore gas dryer stars,glows,blue flame visible and runs for 3-4mins then falme shuts off no oestrus. After it cools it will do the same thing. Is this a thermostat problem?

Janet Hendrickson on September 02, 2010:

Practice you have a picture of the parts for a Speed Queen gas dryer model#AGM499W

BENJAMIN on August 20, 2010:

I have a whirpool dryer model # GLC 6646AN0...NO HEAT AT ALL ,I accept read all your sugestions .and followed step by step..( cheque thermostat.changed coils,bank check continuity on igniter and I got 95.5 Ohms reading .check flame sensor seem to be ok.) simply still no heat..no glowing , no clicking noises ,.is at that place whatsoever thing else to bank check

PS...I got no voltage coming out from the motor switch to the coils.by pressing the starter botton the drum turns merely nada happen ,no oestrus ,any help delight

gary on August twenty, 2010:

i take a kenmore gas dryer that isn't heating upwardly and the timer isn't going off either it just keeps running? i changed the ignitor with no luck, what'due south next the flame sensor???

thanks for any advice....

Ron on July 08, 2010:

I accept a Kenmore Aristocracy Dryer that is virtually iv years old. My married woman claims that when she turned the dryer on, information technology made a popping sound.

She went to cheque the billow and certain enough, information technology was trippped.

She flipped the switch back to on and turned the dryer on.

It runs but has no heat.

I've had the fuses/coils checked and they are good.

I will exist checking the voltage next.

any other ideas on what the cause might be??

Tammy on June 10, 2010:

I have a Amanda dryer replace the Ignitor and nevertheless there is no rut...what could be the problem

winsordidessair73.blogspot.com

Source: https://dengarden.com/appliances/Why-Wont-My-Dryer-Make-Heat

Share this post